Results 1 to 10 of 10

Thread: Help Network Adapter Error 0x800000

  1. #1

    Help Network Adapter Error 0x800000

    Hey I have recently installed a "netgear fa311" network card on RH LINUX 8.0 using the "natsemi dp83815 fast ethernet" driver every thing appears to work ok but when I shut down/start up the computer my screen gets filled several times over with the message: "eth0: pci error 0x800000" I have searched google and I have found plenty of people with a similar problem but with no answer

    if anyone here can help I would highly appreciate it

    James
    http://www.danasoft.com/sig/c0bra.jpg
    click here to hack my computer and delete all my important files

  2. #2
    Senior Member
    Join Date
    Feb 2003
    Location
    Memphis, TN
    Posts
    3,747
    One person suggested downloading a different driver. Heres the link

    http://www.scyld.com/pipermail/netdr...ne/000031.html
    =

  3. #3
    I have three files on disk and they are drivers for RH7 but I don't know how to install them the files are fa31x.o fa3xx.c fa3xx.h makefile r these any good if so could you please give me help on how to install them
    http://www.danasoft.com/sig/c0bra.jpg
    click here to hack my computer and delete all my important files

  4. #4
    Senior Member
    Join Date
    Feb 2003
    Location
    Memphis, TN
    Posts
    3,747
    Ok, I think what you need to do, is ftp to this site
    ftp://ftp.scyld.com/pub/network/

    Grab the file that says netdrives-3.5.tgz

    Once its dowloaded, go inot th folder where it is and type this.

    tar xzf netdrivers-3.5.tgz.

    It should untar it into a new folder, so go into that folder where the new files are now and type this.

    ./configure
    ./make
    ./make install

    Hope fully that will get it. I'm not really good a linux so that might be wrong. If that doesn't work just post back here again, and someone who knows it better than me can help you out.
    =

  5. #5
    the commands you gave me didn't work it said the files cannot be found also it didn't extract to a new folder I have attached a screenshot of the files it extracted
    http://www.danasoft.com/sig/c0bra.jpg
    click here to hack my computer and delete all my important files

  6. #6
    Senior Member
    Join Date
    Feb 2003
    Location
    Memphis, TN
    Posts
    3,747
    hmmm..

    try tar xzyf
    =

  7. #7
    I tried that command and got the following message
    "tar: Old option `f' requires an argument."

    has anyone got any more ideas
    http://www.danasoft.com/sig/c0bra.jpg
    click here to hack my computer and delete all my important files

  8. #8
    somebody please help
    http://www.danasoft.com/sig/c0bra.jpg
    click here to hack my computer and delete all my important files

  9. #9

    Question

    any body else know how to install the drivers (fa31x.o, fa3xx.c, fa3xx.h, and makefile) the drivers are for redhat 7.0 but I am running redhat 8.0
    http://www.danasoft.com/sig/c0bra.jpg
    click here to hack my computer and delete all my important files

  10. #10

    Exclamation

    Somebody here must know
    http://www.danasoft.com/sig/c0bra.jpg
    click here to hack my computer and delete all my important files

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •