-
October 27th, 2003, 03:57 AM
#1
Slackware Problem
Hi everyone,
I've been having a problem trying to get slackware on my computer.
Well I downloaded the slackware ISO file, burned it with Nero and burned it as an image and all that. Now when its finished I put it in my CD-ROM drive and reboot. But it won't boot straight to the disc.(when I installed RedHat it just booted straight to the installing part). I'm wondering if this is something to do with my disc, burning software, my computer... or whatever. If someone could tell me what I'm doing wrong or if I'm doing it right could someone tell me how I can do it another way.
Thanks for anyones help.
-
October 27th, 2003, 04:05 AM
#2
Did you check the md5 sums when you downloaded the iso files. You may have gotten a bad download. It also could have messed up during the burning process. I have always had trouble burning iso's for some reason. I think it was the configuration of my drives though since I had two cdrom drives. It also could have been a bad disc. Check for scratches on the disc. Also, for redhat did you download the files and burn them with the same process, or did you buy the discs or have a friend do it? If you did the same with redhat, I would say that it's not your software or burner, but just a bad download, corrupt file, or a messup in the burning process. When you're burning the iso's, don't do anything else in the background, just set it to burn and come back in about 8 minutes.
Hope I helped
-
October 27th, 2003, 04:10 AM
#3
I tried all different downloads, and tried burning it about 5 different times. Burn process always said finished sucessfully. And I did the same process with redhat, downloaded the ISO files and burned it.
-
October 27th, 2003, 04:25 AM
#4
Try starting the install from boot floppies. The install boot floppy images are located in this directory at this ftp site:
ftp://distro.ibiblio.org/pub/linux/d...-9.1/rootdisks
Just download install 1 and 2 and use rawrite to write the boot floppies. if you already have linux use the dd command:
dd if=path/to/image of=/dev/fd0 bs=36b
I got that command syntax from the suse site so it might be wrong. You might need to change the bs part of it. I have seen this command used other ways, like bs=1kb or something like that, so maybe someone else can help you with the syntax. Anyways, after you have those, go to this directory and download the old_cd.i file which should contain cdrom drivers you can load at boot. Here is the directory:
ftp://distro.ibiblio.org/pub/linux/d...-9.1/bootdisks
Hope this helped.
edit
I'm editing this because I don't think it's old_cd.i you want. Read the following for details.
sorry this is so long but this is off the slackware howto found here:
ftp://distro.ibiblio.org/pub/linux/d...lackware-HOWTO
First, the "IDE" kernels (so named because they do not have drivers for
any SCSI controllers built in):
bare.i This is a kernel to use for installation on most
IDE based PCs, with support for nearly all IDE
controllers and support for IDE/ATAPI CD-ROM/DVD
drives. Most CD-ROM drives made today fall into
this category.
jfs.i A version of bare.i with support for IBM's Journaled
Filesystem. This required patches to the kernel which
you can find in source/k/jfs/ if you need to rebuild
the kernel.
lowmem.i This is a really stripped-down Linux kernel which might
be useful for installing on IDE systems with a low
amount of RAM (less than 8MB). If bare.i runs into
problems, you might try this. NOTE: On systems with
extremely low memory (4MB), ZipSlack plus the
fourmeg.zip add-on (found in the zipslack directory)
may boot and run even in cases where lowmem.i doesn't.
If use have to use lowmem.i to install, you'll then
probably have to compile a custom kernel with the
minimal additional features that your machine requires.
old_cd.i This is a version of bare.i with additional support
for old CD-ROM drives on non-standard proprietary
interfaces. The CD-ROM drives supported by this
kernel are:
Aztech CDA268-01A, Orchid CD-3110, Okano/Wearnes CDD110,
Conrad TXC, CyCDROM CR520, CR540.
Sony CDU31/33a CD-ROM.
Sony CDU531/535 CD-ROM.
Philips/LMS cm206 CD-ROM with cm260 adapter card.
Goldstar R420 CD-ROM (sometimes sold in a 'Reveal
Multimedia Kit').
ISP16/MAD16/Mozart CD-ROM drives.
(Boot time command line options (or 'append=' options
in /etc/lilo.conf) are:
isp16=<port>,<irq>,<dma>,<drive_type>
Valid values for drive_type include: Sanyo, Panasonic
(same as Sanyo), Sony and Mitsumi. Default values are:
port=0x340, irq=0, dma=0, drive_type=Sanyo.)
NON-IDE Mitsumi CD-ROM support.
Optics Storage 8000 AT CD-ROM (the 'DOLPHIN' drive).
Sanyo CDR-H94A CD-ROM support.
Matsushita, Kotobuki, Panasonic, CreativeLabs
(Sound Blaster), Longshine and Teac NON-IDE CD-ROM
support.
pportide.i This is an extended version of bare.i with support for
a wide variety of parallel-port IDE devices. Supports
parallel-port products from MicroSolutions,
Hewlett-Packard, SyQuest, Imation, Avatar, and other
manufacturers.
speakup.i This is like the bare.i (standard IDE) kernel, but has
support for Speakup. Speakup provides access to Linux
for the visually impaired community. It does this by
sending console output to a number of different
hardware speech synthesizers. It provides access to
Linux by making screen review functions available.
For more information about speakup and its drivers
check out http://www.linux-speakup.org.
To use this, you'll need to specify one of the
supported synthesizers on the boot prompt:
speakup.i speakup_synth=synth
where 'synth' is one of the supported speech
synthesizers:
acntpc, acntsa, apolo, audptr, bns, decext, dectlk,
dtlk, ltlk, spkout, txprt
usb.i This kernel is the same as the generic bare.i kernel,
but adds built-in support for USB to allow installing
on machines with USB keyboards.
xt.i MFM (very very old) hard drive support.
Then, the SCSI kernels (these also support IDE):
adaptec.s This kernel supports most Adaptec SCSI controllers,
including these models:
AHA-1510, AHA-1520, AHA-1522, AHA-1522, AHA-1740,
and AHA-2825. The AIC7xxx models, which include the
274x EISA cards; 284x VLB cards; 2902, 2910, 293x,
294x, 394x, 3985 and several other PCI and motherboard
based SCSI controllers from Adaptec. This kernel
also supports all of Adaptec's I2O based RAID
controllers as well as the DPT SmartRaid V cards.
In addition, drivers for OEM Adaptec RAID controllers
used by HP and Dell, and Adaptec branded AAC964/5400
RAID controllers are also included.
ibmmca.s This is a kernel which supports MicroChannel
Architecture, found in some IBM PS/2 machines and
laptops. It is a bus system similar to PCI or ISA.
Support for most MCA SCSI, Ethernet, and Token Ring
adapters is included.
raid.s This is a kernel with support for some hardware SCSI
and IDE RAID controllers. The installer now has
preliminary support for these controllers as well. The
drivers included are:
3ware Hardware ATA-RAID controllers.
AMI MegaRAID 418, 428, 438, 466, 762, 490
and 467 SCSI host adapters.
Compaq Smart Array controllers.
Compaq Smart Array 5xxx controllers.
Highpoint 370 IDE RAID.
Promise Fasttrak(tm) IDE RAID.
IBM ServeRAID hardware RAID controllers.
Mylex DAC960, AcceleRAID, and eXtremeRAID controllers.
Many of these controllers will require some degree of
do-it-yourself setup before and/or after installation.
scsi.s This is a SCSI kernel with support for various
controllers. Note that this kernel does not include
Adaptec support any longer -- you must use the adaptec.s
kernel for that.
This kernel supports these SCSI controllers:
AdvanSys SCSI support (supports all AdvanSys SCSI
controllers, including some SCSI cards included with
HP CD-R/RW drives, the Iomega Jaz Jet SCSI controller,
and the SCSI controller on the Iomega Buz multimedia
adapter)
AM53/79C974 PCI SCSI support
BusLogic SCSI support
EATA ISA/EISA/PCI (DPT and generic EATA/DMA-compliant
boards) support
Generic NCR5380/53c400 SCSI support
Initio 91XXU(W) and Initio 91XXU(W) support
NCR53c406a SCSI support
NCR53c7,8xx SCSI support
SYM53C8XX Version 2 SCSI support
Qlogic ISP SCSI support
Qlogic QLA 1280 SCSI support
scsi2.s This is a SCSI kernel with support for various
controllers not supported by scsi.s.
This kernel supports these SCSI controllers:
Western Digital 7000FASST SCSI support
ACARD 870U/W SCSI host adapter support
Always IN2000 SCSI support
Compaq Fibre Channel 64-bit/66Mhz HBA support
Domex DMX3191D SCSI Host Adapters
DTC 3180/3280 SCSI Host Adapters
EATA-DMA [Obsolete] (DPT, NEC, AT&T, SNI, AST,
Olivetti, Alphatronix) support
EATA-PIO (old DPT PM2001, PM2012A) support
Future Domain 16xx SCSI/AHA-2920A support
Intel/ICP (former GDT SCSI Disk Array) RAID
Controller support
NCR53c710 based SCSI host adapters
NCR53C8XX SCSI support
PAS16 SCSI support
PCI2000I EIDE interface card
PCI2220i EIDE interface card
PSI240i EIDE interface card
Qlogic FAS SCSI support
QLogic ISP FC (ISP2100 SCSI-FCP) support
Seagate ST01/ST02, Future Domain TMC-885/950 SCSI
support.
SYM53c416 SCSI host adapter
Tekram DC390(T), DawiControl 2974 and some onboard
PCnet (Am53/79C974) controllers based on the
Am53C974A chipset
UltraStor 14F, 24F and 34F SCSI-2 host adapters
speakup.s This is the scsi.s (standard SCSI) kernel with support
added for Speakup. Speakup provides access to Linux
for the visually impaired community. It does this by
sending console output to a number of different
hardware speech synthesizers. It provides access to
Linux by making screen review functions available.
For more information about speakup and its drivers
check out http://www.linux-speakup.org.
To use this, you'll need to specify one of the
supported synthesizers on the boot prompt:
speakup.s speakup_synth=synth
where 'synth' is one of the supported speech
synthesizers:
acntpc, acntsa, apolo, audptr, bns, decext, dectlk,
dtlk, ltlk, spkout, txprt
speakup2.s This is the scsi2.s with Speakup support.
speakaha.s This is the adaptec.s with Speakup support.
usb.s This kernel is the same as the scsi.s kernel, but adds
built-in support for USB to allow installing on machines
with USB keyboards.
usb2.s This is the scsi2.s kernel with USB support.
usbaha.s This is the adaptec.s kernel with USB support.
You'll want to choose a kernel from the list that supports your
installation media (such as a CD-ROM drive) and the hard drive you'll be
installing to. For example, to install from an IDE CD-ROM drive to an IDE
hard drive, you'd use the bare.i kernel. Or, for a system with an NCR
53c810 SCSI controller, SCSI CD-ROM, and SCSI hard drive, you'd use either
the scsi.s or scsi2.s kernel (since they each have an NCR driver).
-
October 27th, 2003, 04:31 AM
#5
With nero, when you go to burn the ISO and it has the lil check box saying "Burn as Image file" DONT CLICK THAT. Try another one, and dont click that part, then burn it and ittl be fine.
-
October 27th, 2003, 06:55 AM
#6
i had that problem once what i did is just extracted all the content of the iso with isobuster and copied it into a folder and burned from there and i had no trouble, i also recommend using winiso or Alcohol 120%
-
October 27th, 2003, 12:08 PM
#7
Errmm
You sure about your BIOS boot order ? Just a simple thought.
Greetz,
-
October 30th, 2003, 10:26 AM
#8
Hi kilerboots,
I have had the __exact__ same problem with every Slackware release since 7.0... I actually have
four x86 machines, only one of which will not boot a Slackware iso disk. Each box is either a PII or PIII machine, three with standard IDE CDROM's (el torito compliant, blah blah yada yada), and one with an NEC 16x IDE DVD-ROM; all have Intel mobo's, and just for the record they are Micron PC Client Pro's.
The machine with the NEC DVD won't boot a slackware disk (7.0 - 9.1), but will boot anything else under the sun that I have tried (x86 Solaris, RH, Debian, SCO, etc.). The same Slackware disk boots just fine in the other three boxes.
The ultimate kicker is that the NEC DVD placed in one of the other boxes boots the Slackware iso just fine... It _could_be_ a bios update or something on the one machine, a wierd or more strict manner in which slackware iso images are built, or some kind of black magic, who knows.
That may not have helped much kilerboots, but at least you know you're not alone, and that it _most_likely_ is not the way you burned the disk...
-- spurious
Get OpenSolaris http://www.opensolaris.org/
-
October 30th, 2003, 11:15 AM
#9
Senior Member
If you have a high speed connection, you could always try installing it from FTP :P I find this helpful sometimes when hardware doesn't like to cooperate.
If you're going to do that in this case, you'll have to do as h3r3tic says, and install via the boot floppies.
Creating further mindless stupidity....through mindless automation.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
|