can't update 2K pro to XP Home
Results 1 to 4 of 4

Thread: can't update 2K pro to XP Home

  1. #1
    Junior Member
    Join Date
    May 2002
    Posts
    29

    can't update 2K pro to XP Home

    here's the issue I'm tring to load XP home on to a lap top and when I start to load it I get a message that you can not load XP home over 2K pro. does anyone know why? so after that I tried to go in to command prompt and format the HD and it said that I can't because the system is in use.

    Any Ideas ? What am I doing wrong? what am I missing?

  2. #2
    BANNED
    Join Date
    Nov 2003
    Location
    San Diego
    Posts
    724
    Important If you follow these steps on a hard disk that is not empty, all the data on that hard disk is permanently deleted. We recommend that you back up your hard disk before you follow these steps.

    To partition and format your hard disk by using the Windows XP Setup program:

    1. Insert the Windows XP CD-ROM into your CD-ROM drive or DVD-ROM drive, or insert the first Windows XP Setup disk into the floppy disk drive, and then restart the computer.

    Note To start your computer from the Windows XP CD-ROM (or from the startup disk), your computer must be configured to start from the CD-ROM drive, the DVD-ROM drive, or the floppy disk drive. In some cases, you may have to modify your computer's BIOS settings to set this configuration. For information about how to configure your computer to start from the CD-ROM drive, the DVD-ROM drive, or the floppy disk drive, see the documentation that is included with your computer, or contact the computer manufacturer.
    2. If you are starting the computer from the Windows XP CD-ROM, select any options that are required to start the computer from the CD-ROM drive if you are prompted to do this.

    Note If your hard disk controller requires a third-party original equipment manufacturer (OEM) driver, press F6 to specify the driver.

    For additional information about how to use F6 to supply a third-party OEM device driver while the Windows Setup program is running, click the following article number to view the article in the Microsoft Knowledge Base:

    314859 Limited OEM driver support is available with F6 during Windows XP Setup
    If you are starting from the Windows XP Setup disks, insert each of the additional disks when you are prompted, and then press ENTER to continue after you insert each disk.
    3. At the Welcome to Setup page, press ENTER.
    4. Press F8 to accept the Windows XP Licensing Agreement.
    5. If an existing Windows XP installation is detected, you are prompted to repair it. To bypass the repair, press ESC.
    6. All the existing partitions and the unpartitioned spaces are listed for each physical hard disk. Use the ARROW keys to select the partition or the unpartitioned space where you want to create a new partition. Press D to delete an existing partition, or press C to create a new partition by using unpartitioned space. If you press D to delete an existing partition, you must then press L (or press ENTER, and then press L if it is the System partition) to confirm that you want to delete the partition. Repeat this step for each of the existing partitions that you want to use for the new partition. When all the partitions are deleted, select the remaining unpartitioned space, and then press C to create the new partition.

    Note If you want to create a partition where one or more partitions already exist, you must first delete the existing partition or partitions, and then create the new partition.
    7. Type the size in megabytes (MB) that you want to use for the new partition, and then press ENTER, or just press ENTER to create the partition with the maximum size.
    8. Repeat Steps 4 and 5 to create additional partitions if you want them.
    9. If you want to install Windows XP, use the ARROW keys to select the partition where you want to install Windows XP, and then press ENTER. If you do not want to format the partition and install Windows XP, press F3 two times to quit the Windows Setup program, and then do not follow the remaining steps. In this case, you must use a different utility to format the partition.
    10. Select the format option that you want to use for the partition, and then press ENTER. You have the following options:
    * Format the partition by using the NTFS file system (Quick)
    * Format the partition by using the FAT file system (Quick)
    * Format the partition by using the NTFS file system
    * Format the partition by using the FAT file system
    * Leave the current file system intact (no changes)
    The option to leave the current file system intact is not available if the selected partition is a new partition. The FAT file system option is not available if the selected partition is more than 32 gigabytes (GB). If the partition is larger than 2 GB, the Windows Setup program uses the FAT32 file system (you must press ENTER to confirm). If the partition is smaller than 2 GB, the Windows Setup program uses the FAT16 file system.

    Note If you deleted and created a new System partition, but you are installing Windows XP on a different partition, you will be prompted to select a file system for both the System and startup partitions.
    11. After the Windows Setup program formats the partition, follow the instructions that appear on the screen to continue. After the Windows Setup program is completed, you can use the Disk Management tools in Windows XP to create or format more partitions.

    For additional information about how to use the Windows XP Disk Management tools to partition and format your hard disk, click the following article number to view the article in the Microsoft Knowledge Base:

    309000 How to use Disk Management to configure basic disks in Windows XP
    FROM: http://support.microsoft.com/default...bLN%5d;Q313348
    And a little more info: http://www.microsoft.com/windowsxp/u...october07.mspx
    When death sleeps it dreams of you...

  3. #3
    Junior Member
    Join Date
    May 2002
    Posts
    29
    thanks muretO

    I forget about the ms knowledge base. Just what I needed.

  4. #4
    1337 n00b kryptonic's Avatar
    Join Date
    Sep 2003
    Location
    Tacoma, Washington.
    Posts
    520
    Boot you Win2k disk to command prompt and format that way...It seems to me you are going into command prompt while logged into windows therefore taht is why the system is in use.
    00110001 01101101 00100000 00110101 00110000 00110000 00100000 00110001 00110011 00110011 00110111

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •