February 1st, 2005, 06:40 PM
media state disconnected
I work for 2wire home portal router tech support and I am always getting customer's with error msg "Media state disconnected" when I tell them to do ipconfig.I asked several tech's here and they dont know how to resolve that issue.We usually tell our customer that it is a NIC problem.I believe that there is a way on how to deal with that error instead of redirecting our customers to call their computer manufacturer.I get that error message most likely if they are connected using ETHERNET.But sometimes I also get that error using WIRELESS connection.Can someone help me resolve this issue?Thanks in advance!
February 1st, 2005, 07:30 PM
It just means that they are not connected to the wireless AP. The resolution is simple: get them connected.
To do this means you have to troubleshoot how their AP is set up. Things to consider:
- - SSID: spelled right (it's case-sensitive)? Is it broadcasting or not?
- DHCP: enabled or not?
- Encryption: is encryption enabled?
- MAC: is there MAC address restrictions on the AP?
- NIC Card: is the card seated and working correctly? Is it a wireless card?
- 802.11?: is it the right protocol?
- TCP/IP: is it installed?
- SIgnal strength: Is there anything blocking the signal?
You need to learn how to do troubleshooting and think about these things.
February 1st, 2005, 08:24 PM
just a stupid question, what is AP?
February 1st, 2005, 08:25 PM
and one more thing..how to view if DHCP is enabled?
February 1st, 2005, 08:33 PM
Well, you need to check on the AP itself (usually a web interface via wired connection). Additionally the NIC card has DHCP enabled via the properties of the NIC using Right-Click on the mouse (Network Neighbourhood ---> Properties ---> Select the Network in question ---> Properties ---> General Tab ... go to TCP/IP and the select Properties and ensure that Obtain Address Automatically is enabled).
AP= Access Point
February 1st, 2005, 09:13 PM
cool. Thanks..oh by the way.What if the IP address is 169.x.x.x and there is no default gateway and the LAN status is showing up NETWORK CABLE UNPLUGGED.I told my customer to release/renew the IP but still getting thesame IP address with no subnet and default gateway.I already checked on the NIC card if it is installed properly and disabled the firewall or antivirus.Is there something wrong with the NIC itself?
February 1st, 2005, 09:17 PM
Could be something wrong with it. The 169.x.x.x address is the default address assigned to a NIC, by Microsoft OSes, that cannot get a DHCP address.
Are you sure that there is a DHCP server running?
February 1st, 2005, 09:19 PM
169.x.x.x is given when your nic is set to DHCP...but cant find a DHCP server to get one from??
Thats why it wont renew
If you can ping 127.0.0.1...
your NIC is ok
Next would be the cable...try a different one...one you know works??
Can they ping the router\AP they are connected to??
Can they tracert to a common site such as www.google.com ???
What are all the errors???
How people treat you is their karma- how you react is yours-Wayne Dyer
February 1st, 2005, 11:41 PM
Firstly I will say that I really can't believe that your company is hiring tech support staff with your level of knowledge.... I would recommend that you go to your supervisor and tell them that you need more training in the basic of the operating systems you are most commonly dealing with.
This isn't a cruel Microsoft joke... honest.... If it says the network cable is unplugged then, at a minimum the cable is bad and shows no connectivity, otherwise it really is unplugged or the device it is connected to is switched off.... There, that wasn't all that hard was it?
Well.... You obviously know how to do an ipconfig /all.... but did you ever read the output.... It tells you quite clearly that DHCP is enabled or not..... Again... Not too difficult......
and one more thing..how to view if DHCP is enabled?
OK... so I have been nasty for a while..... but lets look at the problem - and I'm speculating a little here.... You mentioned it's when they are trying to connect via Ethernet.... Silly question maybe.... is 2wire a DSL service?... Because DSL usually seems to connect via PPOE, which is different and requires a username and password amongst other things....
Also, Ms. M. is right... Are they expected to connect to to a DHCP server over ethernet, (ie: they have a router?), or are they supposed to connect to you over PPOE and subsequently get an address DHCPed to them after the PPOE connection is complete....
Don\'t SYN us.... We\'ll SYN you.....
\"A nation that draws too broad a difference between its scholars and its warriors will have its thinking done by cowards, and its fighting done by fools.\" - Thucydides
February 3rd, 2005, 10:45 PM
Sometimes I wonder if THAT is the mystery to why outsourcing techsupport to other countries is so popular... knowledge and more so the ethics or drive to actually fix a problem versus just getting through a script.
I really can't believe that your company is hiring tech support staff with your level of knowledge
West of House
You are standing in an open field west of a white house, with a boarded front door.
There is a small mailbox here.