-
November 23rd, 2006, 07:34 PM
#1
Junior Member
okay is this possible
right is it possible to get one computer to talk to another through two wireless routers?
eg
Computer1--(cable)--W.router --(wireless)--W.router--(cable)--Computer 2
-
November 23rd, 2006, 08:07 PM
#2
yes its possible if they are in the same domain/workgroup in windows.
-
November 24th, 2006, 02:01 AM
#3
Hey Hey,
First off... WTF does workgroup/domain in Windows have to do with two computers communicating.. (xenogamer == idiot, no offense)
Now... on to the question..
Computer -- Wireless Router --- Wireless Router --- Computer
That's what I see.. so you're basically saying
i) No Internet Connection involved
ii) Computer A is connected to WiFiRouter A
iii) Computer B is connected to WiFiRouter B
iv) Router A is connected to Router B
The answer is... It depends on the routers...
One of the two routers requires the ability to connect to the other router..
Linksys -- WRT54G supports this (Not sure if it's with default firmware though) -- BEFW11S3 doesn't... So check your routers documentation on the modes that it supports.
-
November 25th, 2006, 11:54 AM
#4
Rather than using wireless routers, if you shun their routing ability, and just make them behave as bridges, then you can certainly do this.
Routing is a red herring- you don't need any routing to do the above. Simply configure the two accesspoints as bridges (which they usually do by default), and it will work.
Of course if these have built-in DHCP servers, at least one of them must be disabled. Both must have static IP addresses which are on the same netblock but not the same and not in the DHCP range.
But the IP address of the accesspoints is irrelevant in two PCs talking to each other.
Two PCs will be able to talk if:
- They are both on the same ethernet segment, logically (Seeing as most accesspoints behave as bridges, it's logically the same ethernet segment)
- They have IP addresses in the same netblock (usually the easiest way of doing this is having them both assigned by the same DHCP server)
Mark
-
November 25th, 2006, 04:01 PM
#5
I'm a bit confused by this.
The OP wanted to connect a cable from each PC to a router and then allow the routers to connect to each other, so allowing the PCs to talk to each other wirelessly. Would it be possible to cut out one of the routers so a single router is connected to PC(1) via a cable and then PC(2) connects to the router wirelessly? This would be cheaper - if it worked.
The comment of slarty is interesting - presumably connect each PC to an accesspoint via a cable and then allow the accesspoints to communicate? Again, I'd ask if the second accesspoint is necessary - could PC(2) connect wirelessly to the accesspoint which is connected to PC(1) via the cable?
-
November 25th, 2006, 08:48 PM
#6
I think if you re-read it, poster just wants two PC's to connect wirelessly
IP config / domain not withstanding
Yes they can talk
just bear in mind HT's bit
they have to be compatable
standard connection would be telecom to router [cable]to PC [wireless]
poster wants two routers ..............
and he wants cable to the routers
anyone else see the upcoming problems with this scenario ........
maybe poster could add details
some whys wouldn't be amiss
so now I'm in my SIXTIES FFS
WTAF, how did that happen, so no more alterations to the sig, it will remain as is now
Beware of Geeks bearing GIF's
come and waste the day :P at The Taz Zone
-
November 30th, 2006, 10:06 AM
#7
I think I completely misread the question- I described a scenario for having two wireless nodes out of range of each other talking via a pair of accesspoints and a wired network.
What the OP wanted to do was quite the opposite - have two wired nodes communicate via a wifi segment in the middle.
The latter is certainly possible but only with certain models of accesspoint. At least one of the accesspoints/routers needs to be capable of operating as a wifi "client" node (rather than an access point per se).
Some also support a "Distribution node" mode- I think maybe this can be used to implement the OP's requirement as well.
Slarty
-
November 30th, 2006, 04:46 PM
#8
Do you know of any accesspoints/routers that can operate in both modes? I have a Netgear router and it only works in "standard" mode.
-
December 2nd, 2006, 12:17 AM
#9
MSI do USB / PCMCIA / PCI versions of a wireless card, that can be swithed into AP mode too, so you could have one set as AP and one as client ??
but now a second question
WHY ???
so now I'm in my SIXTIES FFS
WTAF, how did that happen, so no more alterations to the sig, it will remain as is now
Beware of Geeks bearing GIF's
come and waste the day :P at The Taz Zone
-
December 2nd, 2006, 10:37 AM
#10
I know that I can link two PCs directly via a cross-over cable for file sharing, backup etc., and I just wanted to know if I could do the same thing wirelessly.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
|