-
October 2nd, 2007, 04:01 PM
#1
WAP Locating App
I tried looking on here quickly but didnt find what I am looking for.
I want to assess my network in a building that is over a million square feet.
I am looking to locate all AP's Rogue and ones that belong.
I am open to using *nix or Windows App
I dont want to really spend any more money
The current infrastructure is Cisco Based
My Setup:
Dell D620 laptop
Cisco Aironet Air CB21AG-A-K9 Card 802.11 A/B/G
Running Windows XP
What I have tried:
We have an application called AirMagnet which is good but only licensed to one of our laptops and I am really hoping there might be something Open Source out there that is better.
I booted off a Distro Called BackTrack which is a compilation of Whax and some others I think. I used Kismet and while it was a good application I really want something that will home me in on the exact location of the AP.
What I want
Find AP's whether or not they are broadcasting their SSID
See if People are connected to it
Home in on the exact location of the Signal
Pull MAC of the AP
Attempt to connect to the AP
my knowledge in linux is limited but there is a willingness to learn if it is beneficial.
I appreciate any advice that anyone can offer.
Thanks
Spy
Edit... I cant spell
Last edited by Spyrus; October 2nd, 2007 at 05:13 PM.
Duct tape.....A whole lot of Duct Tape
Spyware/Adaware problem click
here
-
October 2nd, 2007, 04:11 PM
#2
For you to "home in" on AP you would preferably need a GPS receiver so you can correlate the AP's signal strength to your position. Kismet can handle that and everything else too.
Kismet+GPS and start walking. After that you can analyze the data and make beautiful colored maps.
Another way to "home in" is by using a directional antenna and looking at the signal strength..
Oliver's Law:
Experience is something you don't get until just after you need it.
-
October 2nd, 2007, 05:14 PM
#3
Where would one find a GPS receiver for this application?
Duct tape.....A whole lot of Duct Tape
Spyware/Adaware problem click
here
-
October 2nd, 2007, 05:30 PM
#4
-
October 2nd, 2007, 05:40 PM
#5
I used NetStumbler last winter in a similar situation to track down a
rogue WAP in our plant. It's a free Windows app that'll give you the
signal strengths for anything broadcasting on all eleven 802.11 wifi
channels. One of the contract engineers had ran a wireless router
off a drop on the assembly floor. After fielding several questions from
our users about the "new" WAP and a comment of the VP in charge
of IT, I installed NetStumbler on a loaner laptop and proceeded to do
a walkabout in the plant. I was able to find it by simply gauging the
signal strength as I moved around. It wasn't the fanciest way to track
down the rogue WAP, but the price was right.
To see the people connected to it, I was able to simply login as the
router still was in a factory config. My favorite method for checking the
"population" of any given network is to run Ettercap and scan for hosts.
It's pretty simple to do, even from Windows. I run a VM (VMWare Player
or Workstation) and launch a security Linux distro like Nubuntu or Back-
Track to run Ettercap. You could use the same method to run nmap
to portscan the IP address of the rogue WAP and that should give you
the MAC address. Nmap also runs from Windows if you install WinPCap
too.
If you got the money for a GPS receiver, great, but that's probably a bit
of overkill.
“Everybody is ignorant, only on different subjects.” — Will Rogers
-
October 2nd, 2007, 09:16 PM
#6
If your laptop has bluetooth you can use those same GPS "mouse" receivers they're using with those mobile navigators. Works like a charm
One note though.. NetStumbler is an active scanner. It sends out a probe and listens for APs responding. An AP with SSID broadcasts turned off will not respond to these probes. Kismet is a passive scanner. It just listens and will find any wireless network (there's always some traffic needed).
Oliver's Law:
Experience is something you don't get until just after you need it.
-
October 3rd, 2007, 10:31 AM
#7
Originally Posted by SirDice
Kismet is a passive scanner. It just listens and will find any wireless network (there's always some traffic needed).
Duly noted, SirDice. Thanks.
“Everybody is ignorant, only on different subjects.” — Will Rogers
Similar Threads
-
By Spyrus in forum Network Security Discussions
Replies: 11
Last Post: May 16th, 2005, 06:02 PM
-
By nixkl in forum Site Feedback/Questions/Suggestions
Replies: 2
Last Post: April 5th, 2003, 01:36 AM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
|