November 7th, 2007 11:21 PM
joining two network ports together
i am not sure what you call this
at work we have two ports side by side to plug you computer/laptop into.
if you take one network cable and plug one end into one output and the other end into the other output this crashes the network
is there a way to pick up where this happens or prevent the network from crashing?
the network is dhcp
and uses an proxy prior
(if i have repeted this sorry)
like life, this is a test
November 8th, 2007 03:05 AM
What kind of router / switch is this?
I know what your talking about, as I accidentally plugged the same switch into itself by accident once which brought down all nodes on that switch. However, I cannot think of the term right now. Though loopback does sound plausible.
Depending on the router / switch it might be able to log when this happens, if its a lower end switch, I would imagine that your somewhat out of luck as far as being to catch this electronic wise via logging.
Next question would be, why are you having this probelm in the first place? is anyone allowed to plug / unplug cables into the router switch?
November 8th, 2007 07:16 AM
this does not have to happen at the switch level (these are locked away anyhow)
basically where the network cables come out of the wall if you unplug one
from the wall, unplug the second cable from the back of the other computer and then plug that back in the now empty slot you get network shutdown
do not know if it is logged as i takes ages to go around the site to find where it happens
like life, this is a test
November 9th, 2007 03:22 AM
That does present a bit of a problem.
Is it the same jack / network plate all the time that someone is doing this? Or is someone doing this at random jacks?
November 9th, 2007 05:24 AM
If you use Cisco switches you can use "bdpu guard" to prevent a loop from taking down a network.
November 9th, 2007 08:40 AM
Another way to prevent this of course is to disconnect the premise wiring from the switch at the patch panel. This would also prevent unauthorized workstations from getting on your LAN.
"Somehow saying I told you so just doesn't cover it" Will Smith in I, Robot
November 9th, 2007 10:29 PM
Is there anything similiar to that for HP Procurve managed switches?
Originally Posted by Net2Infinity
November 12th, 2007 06:10 PM
Don't all switches these days use spanning tree protocols?
November 12th, 2007 07:04 PM
That's a loopback alright. I'm sure most modern umanaged switches will detect it and I'm quite sure managed switches support STP..
But STP might be the cause the network is "crashing". Recalculating the tree can take a long time if not configured correctly and the entire network will be down in the mean time.
If the network is anything like I've seen, add a switch here, there.. Few months later another there.. etc.. it might need a major reconfiguration.
Another good thing to do (and boost your security a bit) is to disable all unused ports on your switches. You can stick anything[*] in a disabled port, it won't work.
[*] Not really anything though.. 220 volts does some fecking gawdawful things to a switch
Last edited by SirDice; November 12th, 2007 at 07:15 PM.
Experience is something you don't get until just after you need it.
November 12th, 2007 07:20 PM
True I didn't think about multiple switches, different firmware, hardware, stuff like that.
Originally Posted by SirDice
#1 rule of thumb is the locking unused ports. Most of the higher end switches you can configure to allow "registered mac addresses" but that's a whole nother story.
So uh Dice...
Why do I get the feeling that you have first hand knowledge of 220 volts pulsing through a rj 45 port?
By instronics in forum The Security Tutorials Forum
Last Post: January 8th, 2010, 11:30 PM
By Tiger Shark in forum Firewall & Honeypot Discussions
Last Post: December 1st, 2004, 11:15 PM
By Computernerd22 in forum Network Security Discussions
Last Post: July 18th, 2003, 04:36 PM
By Noble Hamlet in forum AntiOnline's General Chit Chat
Last Post: March 17th, 2002, 08:38 AM
By Remote_Access_ in forum Security Archives
Last Post: January 2nd, 2002, 03:50 PM