Printable View
I run partition magic 7 or 8 on my OS (windows xp) and it sais this...
Error #90
EZ-Drive has been detected on drive 1, but EZ Drive is corrupt. Run the EZ-Drive setup disket to correct this problem. For EZ-Drive support contact your EZ-Drive provider.
ok...wtf is this...?
and btw: on WinME it goes fine without errors but on WinXP i cant run Partition Magic at all
any help? ...thanks in advance
found here http://www.patoche.org/LTT/windows/00000117.htmlQuote:
If you have a large hard disk and an old computer that doesn't support them then
you probably got a utility called EZ-Drive or Disk Doctor with you hard disk.
You need it to use your entire hard disk with Dos and Windows but not Linux.
However, if you dual-boot DOS/Windows and Linux, you still need it. The bad
part about them is that they don't support Linux. To get around this, simply
install LILO to your root partition's boot record instead of your master boot
record and set your boot flag to your root partition.
To install LILO to the root partition's boot record during install simply select
the root partition as where to put LILO when your Linux installer asks you (Most
distributions do but some automatically put LILO on the master boot record. in
that case ask someone else what to do because I'm stumped on that one.).
[ note of maintainer : you add to use boot=/dev/hda1 for example if /dev/hda1 is
your root partition instead of boot=/dev/hda (in that case lilo will install itself
in the mbr - master boot record - of disk /dev/hda ]
NOTE: YOU MUST INSTALL EZ-DRIVE OR DISK DOCTOR FIRST!!! DOS/WINDOWS MUST GO
ON SECOND.
found by... http://www.google.com.au/search?sour...8&q=EZ%2DDrive
well in simple terms.. it is a Boot overlay.. like EZBIOS etc..
Cheers
my disk1 is my 40GB disk and never had that problem before but now i do since i have another 80gb disk (disk2)...so what should i do now download that ?Quote:
If you have a large hard disk and an old computer that doesn't support them then
you probably got a utility called EZ-Drive or Disk Doctor with you hard disk.
You need it to use your entire hard disk with Dos and Windows but not Linux.
How exactly do i install something with no OS on it at all...Quote:
NOTE: YOU MUST INSTALL EZ-DRIVE OR DISK DOCTOR FIRST!!! DOS/WINDOWS MUST GO
ON SECOND.
EZdrive will boot into caldera dos or something like that, and you can install through that because you have effectively loaded an OS.
Does your BIOS support 40 and 80 Gig drives?, if so, I do not see what you are running EZdrive for anyway?
Are you dual booting XP and Me?
Are you sure that your version of partition magic supports XP?
It sounds as if you had XP and Me running OK on the 40Gb drive, but have hit problems when you installed the 80Gb drive as "D"? Is this correct?
Have you tried to update your BIOS?
Have you tried to move one of the operating systems?
Cheers
I know for fact that PM 7 and 8 work on winXP... I'm using it almost every day...
Can you tell us your exact configuration earlier and now when you added 80GB disk (master/slave, primary/secundary) and location of both OSes...
right now like this:
Disk1: master boot
Partition1: 10GB (WindowsXP, fat32)
Partition2: 25GB (Data, fat32)
Partition3: 5GB (System Sav, fat32)
Disk2: slave
Before:
Disk1:
Partition1: 35GB (WindowsXP)
Partition2: 5GB (System Sav)
Nihil...i dont know if my BIOS supports 80gb hard disks....i tried updating it once but unsecussful because i dont know which one it is....back then it displayed 35GB instead of 80GB and im using a boot disket to recognize my WD800JB disk to 80GB but it formats the whole disk...i am not dual booting the XP and Me....and i dont know if partition magic 8.0 supports my XP...if not is there something else i could use?
Partition1: 80GB (Data, ntfs)
EZ drive is often shipped with new hard drives. It comes on a bootable floppy disk.
If your BIOS does not support drives that big, you boot from the floppy
and it installs a special program on the first track of the HD, and relocates the
MBR to the second track. Your OS and most other software cannot see
the EZ drive track, and happily uses the disk.
What you need to do depends on whether the disk is functioning satisfactorily.
It sounds like you are trying to resize your partitions. Is this drive still functioning as a
boot drive? EZ drive may be incompatible with partition magic, if partition magic
is looking in the wrong sector for the Master Boot Record.
If the drive is working OK otherwise, I wouldn't monkey with it
If you want to experiment, you could wipe out EZ drive, and the MBR,
and try partitioning the drive afresh. Your BIOS should support a 40 gig
drive unless it's really old (486 or Pentium I)
:cool:
http://www.acree.ugate.net/Downloads...Clean-MBR.htmlCode:A program called DEBUG.EXE is supplied with DOS, Windows 9x and NT and
can be used to run small Assembly language programs and just such a program
can be used to wipe the MBR. Perform the following, but BE CAREFUL, this WILL
wipe your MBR leaving your system unbootable and its data lost.
Boot to 9x or DOS (this cannot be done from NT since direct disk access is not allowed)
Start a command prompt
Enter the following commands (in bold):
C:\> debug
-F 9000:0 L 200 0
-a
0C5A:0100 Mov dx,9000
0C5A:0103 Mov es,dx
0C5A:0105 Xor bx,bx
0C5A:0107 Mov cx,0001
0C5A:0109 Mov dx,0080
0C5A:010A Mov ax,0301
0C5A:010D Int 13
0C5A:0110 Int 20
-u 100 L 12
-g
Program terminated normally
-quit
all i want to do is merge the 2 partitions in disk 1 and then split them again so i have more space on XP...now i dont see why i am getting this error....maybe its just the partition magic...is there some other partitioning software i can use to partition my disks without loosing data?
Hi,
Sorry for the delay in responding, seems to be a bit of a problem getting into AO through the front door today?
I do not quite understand where Me fits into the equation? (looking at your system specs)
If you just want to run XP, then why not remove the 40Gb drive and set up the 80 as your primary drive with XP.
Then add the 40 as a slave..............transfer whatever you want from it..............reformat your 40 drive, and away you go? You should be able to set up whatever partitions you want this way?
If you want to run Me, then you have to load this as your primary OS, then load XP? You will boot into XP but you will get the dual boot option.
You have to remember that Me will only use FAT32 whilst XP can use either FAT32 or NTFS, but needs (AFAIK?) to be set to FAT32 if you want to use both systems on both drives.
You also have to realise that if you have OEM, rather than boxed versions of you OSes, they are "protected" ( ;) ) against being loaded as anything other than the only OS on your machine.
Hope this helps
I am not asking to dual boot right now....all i want is to merge 2 partitions and then split them again without loosing data and partition magic wont run...so is there something else?
and i cant switch the two disks because my 80GB disk shows up as 35 first time when i start windowsXP and so on....only way i found to fix it was with a boot disket i downloaded from the internet which corrects this but deletes all the files on it...so you see why i cant set the 80GB disk as primary?
You might try:
http://www.pcworld.com/downloads/fil...id,6170,00.asp
or google search for "partition manager"
You should be able to find one that works?
Also, have you enough space on the 40 to copy the data you have on the 80? If so go for it, then remove the 40 and install the 80 as primary?
Know anyone who is just building a new box who could lend you a drive for a day?
Just a few thoughts?
cheers
My post before this one explains why i cant do it...did you read it?
my 80GB disk kind of resets itself when i install XP onto Me...it shows 35 instead of 80 and the only way i know of fixing is running my boot disk which fixes the problem but DELETES ALL DATA on the 80GB disk....so thats why i must keep my 40GB the primary...but ill see what i can do about the partitioning thing