I tried to install SUSU 9.1 personal on an old box. It's 233mhz with 64mb ram and a 2gb hard drive. It says it doesn't have enough memory to load YaSt, and it asks for the swap partition. I don't have a swap partition yet, so what can I do?
Printable View
I tried to install SUSU 9.1 personal on an old box. It's 233mhz with 64mb ram and a 2gb hard drive. It says it doesn't have enough memory to load YaSt, and it asks for the swap partition. I don't have a swap partition yet, so what can I do?
From the SUSE support area:
Looks like you are about 64 megs short of being able to run it. If it is giving you this error during installation, there isn't a single thing you can do besides using a different distrobution (with those specs I recommend slackware or a BSD flavor) or upgrading the RAM. If it is happening after installation and while you are using it (you shouldn't have been able to get this far) then look into the tools SUSE gives you for repartitioning.Quote:
origional text: http://www.suse.com/us/private/suppo...onditions.html
Installation on a typical, private, standalone PC or laptop with a single-processor system, with at least 64 MB RAM (as of SUSE LINUX 9.1 128 MB) and 2 GB free space on the hard disk
So, the answer I need from you is: Are you getting this error during installation or after installation for normal everyday use?
I'm getting it during installation.
I'm not trying to sound like an *******:
When you don't have the MINIMUM amount of RAM to use it, then why are you even posting saying you can't install it? Of course you can't, you don't have enough RAM. This is why they put the requirements on the box. When you install something, the first thing you should be doing is checking if you have the proper resources to run it.
What does this have to do with *NIX security?
http://rinkworks.com/stupid/cs_hardware.shtml
from the suse instalation readme:
System requirements
You need at least 96MB main memory. To install on a machine with less
memory a (linux) swap partition is necessary.
he cant just make a swap partition?
How do I make a swap partition? It asks me for the swap partition when it gives me the error, so I'm pretty sure it's possible.
You can't make a swap partition, you only have a 2gb drive which is required for installation. You'll either have to get more ram or another hard drive.
Actually, the requirements say 400mb minimum, but 2gb recommended.
A 400mb install is the bare bones install, won't have much fun with that, but it does function properly. He can make a pretty good install of SuSE with 1gb and have 1 left. But you still must meet the memory requirement.
Also sounds like you are attempting a default install. After you get another ram stick, it will make the swap partition and the / partition for you.
Do some searching on AO for partitioning etc., it's not that difficult and most likely, eventually you'll be doing it anyway.
cheers
:cool:
Ok. I've never bought additional RAM before, so can you advise me on what's a reasonable price and how much I should get? Also, I should be able to figure out where to plug it in pretty easily, right?
Jareds411,
I believe the 233 uses 72-pin SIMM Memory Sticks and the price used to be $1.00 per MB and I would imagine it might be close to that now. However shop around on www.google.com and you should be able to find it cheaper than that. Additionally you need to check your main board book to see how much you can add and how many slots you have etc. It is simple to install, but remember "static electricity" can ruin your whole day and components inside your computer. I shutdown the computer, unplug it from the wall, open the side cover, and use my grounding wrist band to take care of the static electricity, but you may not have one of them, so make sure you touch the actual chasis of you box, before every touching anything else. If I'm not using a strap, I leave some part of my bare skin touching the frame. Anyway your book will give you a pretty straight forward guide to installing the memory.Quote:
233mhz with 64mb ram and a 2gb hard drive
cheers