WindowsUpdate after SP2

Printable View

October 7th, 2004, 08:05 PM
Cyberlord

WindowsUpdate after SP2

Hi all.
Long time since I posted something...Sorry if this is the wrong forum.
Anyway, I have a problem downloading updates from Windows Update site. It just stays there checking but nothing happens, only the progress bar moving and after a while IE closes.
This began to happen after installation of SP2, before that, it used to work just fine.
I've tried registering several libraries, executing some procedures but right now I'm out of ideas as to why this is happening.
By the way, checking the Windowsupdate.log file, I've found these error codes 0x80246005, 0x8024000c, 0x8024400d
I have a dialup connection, and no proxies or firewalls installed, just SP2. I tried disabling windows firewall and no change.
So any idea will be very appreciated.
October 7th, 2004, 08:09 PM
MrLinus

Hrmm.. Rumor is that SP2 can be applied to cracked Windows copies but after that, you won't be able to apply anything else. So.. errr.. ummm... is your's a legit copy?
October 7th, 2004, 08:26 PM
Cyberlord

Well MsMittens, I haven't heard that yet, but, yes, mine is a legal copy.
Any ideas?
October 7th, 2004, 08:34 PM
MrLinus

Hrmm... have you installed anything else since SP2?
October 7th, 2004, 08:36 PM
Cyberlord

No, just right after that, I went to windowsupdate, and problems began....
October 7th, 2004, 08:42 PM
MrLinus

Have you done the standard check for virus and spyware (perhaps they are interfering with it?)
October 7th, 2004, 08:49 PM
cacosapo

Re: WindowsUpdate after SP2

Quote:

0x80246005

take a look here:
http://support.microsoft.com/default...b;EN-US;241783

see if it helps you
October 7th, 2004, 09:59 PM
Neptune0z

Ok...After reading your post the first thing that I though was a network connect problem...Like trying to update thru a firewall, a proxy or something like that. But towards the end of your
message you state that both are not installed on your system. Two's of those error messages I've seen before (0x80246005, 0x8024000c) and they do relate to network connections. However, that last one (0x8024400d) I've never seen (and after doing a search on MSN, apparently neither has Microsoft.). So I'm not really sure what the specifc's of your problem is.
Usually, when something goes bad with AutomaticUpdate, it's caused by an interrupted install.
I think it's possible that what happened was during your last update, the process was interrupted by something. I did notice you had a dialup connection, could it be possible that your install was interrupted by call waiting? If not, then it's still possible that an application or service did it. Restore points are your friend :). I would try the update one more time, but this time make sure no unnecassary programs are running and if you have call waiting, turn it off for a while. If you have access to a fast connection, you might try downloading the file install version of SP2 from Microsofts sites (I think it's 200 - 300 mb). This will install much as a regular program would, and completely avoids all the complexites in AutomaticUpdate. In addition it has many additional drivers and install mechanisms which tend to 'get along better' with other 'progs...See if that helps...
October 7th, 2004, 10:26 PM
AngelicKnight

Now I had something similar happen actually. I figured out the fix, but it never made a lick of sense.

I tried to install SP2 on a client's machine, but it would hang up when running the update. I would get the blue progress bar that scrolls back and forth. Well, I opened up another Window to go to another website, and as soon as I did that, update unfroze!

Tried it again...Update froze. Again, opened a second window, surfed to a different site, then went back to the first window...Update resumed.

Very wierd, but it worked. I'll never know why!
October 13th, 2004, 06:18 PM
Cyberlord

Thanks guys for the tips.
Sorry I've been out of town, so I'l try that and let you know.
Thanks again
October 13th, 2004, 07:29 PM
MrLinus

Quote:

I tried to install SP2 on a client's machine, but it would hang up when running the update. I would get the blue progress bar that scrolls back and forth. Well, I opened up another Window to go to another website, and as soon as I did that, update unfroze!

Tried it again...Update froze. Again, opened a second window, surfed to a different site, then went back to the first window...Update resumed.

Perhaps this is related to an issue I've noticed. When doing updates it's rather slow until I remove the firewall. Then it just zips along. I'll have to fire up the ol' packet sniffer the next time I connect and see what's passing through but on the surface there seems to be a request that needs to be legitimately made that perhaps the firewall is blocking or that it doesn't like that the firewall (Sygate?) running?