-
January 30th, 2002, 08:47 PM
#1
Senior Member
Hiding Linux Partition From Windows
I am dual booting between Windows ME and Red Hat 7.2 with Grub. For whatever reason my Linux partition is showing up under Win Me as drive 'D'.
I had this problem once when I used to boot with Lilo- but then by accident I erased my MBR and had to re-install lilo - which in effect fixed it.
If anyone had some thoughts on how I can hide my Linux Partition from windows it would be greatly appreciated.
-
January 30th, 2002, 08:56 PM
#2
with win98 you can use TweakUI, I'm not sure if it workse with ME?
You could try a different filesystem for *nix as well.
-
January 30th, 2002, 08:58 PM
#3
Just a thought. how did you format the linux partition ? if you did it as any sort of FAT partition it will be seen through windows. Try using ext3fs. That should take care of it.
Antionline in a nutshell
\"You\'re putting the fate of the world in the hands of a bunch of idiots I wouldn\'t trust with a potato gun\"
Trust your Technolust
-
January 31st, 2002, 06:26 AM
#4
Senior Member
It has been formated as ext3- I didn't think linux would boot off a FAT partition. I'll give TweekUI a try, thanks.
-
February 4th, 2002, 05:38 AM
#5
Senior Member
Ok, TweakUI doesn't work with Windows Me.
I just realized that I should have probably specified that it is not hiding the file system but hiding the partition from windows so that it does not show up as drive D: - b/c anytime a program goes to open drive D: it prompts the good old question "Do you want to format drive D:\?" And I can't have anyone else or even myself clicking format.
I do see with grub there is a hide command. I was wondering what this does, and if/how I can use it?
-
February 6th, 2002, 05:29 PM
#6
Run fdisk (from linux) and check the partition's
ID number. You may get a clue there.
Windows shouldn't see it if it is linux native, type 83
It's possible that linux could format and use the
partition succesfully, but it is flagged in the partition
table as a FAT partition (even though you actually
have an ext3 filesystem on it)
I came in to the world with nothing. I still have most of it.
-
February 7th, 2002, 05:17 PM
#7
Senior Member
Ok here is my partitions/ ID
Devide ID
/dev/hda1 c
/dev/hda2 5
/dev/hda5 82
/dev/hda6 83
/dev/hda7 83
As you can see my / and /home partitions, hda6 & hda7, are type 83 (Linux etx3) - my swap is type 82 (linux swap) - and of course my windows partition is type c (FAT32 LBA) - and hda is my extended type 5.
I wonder if it because I have hda2 as an extended.
-
February 7th, 2002, 05:29 PM
#8
I believe 83 is actually ext2, not ext3, but that is beside the point. Although if you go to ext3, that may solve your problem. I also thought that extended was type 0F (hex) and fat 32 (your primary) is type 0B. Not sure what 0C and 05 are....
Anyway, I have never seen any linux partion show up in windows, unless it was on another computer and mapped with Samba. There almost has to be something wrong with your boot loader to do this. If you have a boot disk, I would be tempted to fdisk /mbr in dos, boot to linux with the disk, and reinstall grub or lilo or whatever you want to use...
\"Ignorance is bliss....
but only for your enemy\"
-- souleman
-
February 7th, 2002, 06:17 PM
#9
83 = ext2
I don't know the code for ext3...
but howcome your ext2/3 is seen in win...
It doesn't show up on any of my dual boot machines... (98 nor XP)
ASCII stupid question, get a stupid ANSI.
When in Russia, pet a PETSCII.
Get your ass over to SLAYRadio the best station for C64 Remixes !
-
February 7th, 2002, 09:54 PM
#10
Senior Member
I wrote ext3 because thats what it is formated as. Fdisk lists 0C as "FAT32 LBA" and type 05 as extended, for type 83 it just says linux so I assume both ext2 and ext3 use type 83 (I know for sure b/c when I upgraded my kernel I forgot to add ext3 support and it wouldn't boot the new kernel).
I did once re-install lilo and that solved my problem , but then when I changed to grub it happened again. I am kinda tempted to fdisk mbr and re-install grub, but my last experiance with that I accedently installed it to hda1 (long story) and overwrote my Windows boot (by that I found out that sector 6 of my Win partition was a backup of sector 0 so I just copied sector 6 over sector 0 and booted up again). But if there are no other suggestions I might just do it- and I'll be careful not to do anything stupid this time. Thanks
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
|